 Produces excellent final finish especially on stone and metal. $46.56 |  Finely ground and bonded with rouge to produce a gleaming final finish on metal and stone. $59.14 |
 Formulated for very fine surface conditioning. Low R.M.S. finishes are commonly achieved. Plastic medias are widely used in the precision metal industries. Also due to fine surface finishes achieved, parts are prepared for preplate, pre-anodize, or decorative polishing. Brown, V-cut, Cone (medium cut, Green (light cut), and White (very fine cut). Density-55lb. per cu. ft. 1/4". $75.50 |  Used dry, produces a brighter finish when tumbled for 12 to 24 hours. Absorbs moisture. $98.11 |
 Formulated for very fine surface conditioning. Low R.M.S. finishes are commonly achieved. Plastic medias are widely used in the precision metal industries. Also due to fine surface finishes achieved, parts are prepared for preplate, pre-anodize, or decorative polishing. Brown, V-cut, Cone (medium cut, Green (light cut), and White (very fine cut). Density-55lb. per cu. ft. 1/4" $82.26 |  Formulated for very fine surface conditioning. Low R.M.S. finishes are commonly achieved. Plastic medias are widely used in the precision metal industries. Also due to fine surface finishes achieved, parts are prepared for preplate, pre-anodize, or decorative polishing. Brown, V-cut, Cone (medium cut, Green (light cut), and White (very fine cut). Density-55lb. per cu. ft. 1/4". $82.26 |
 The alternative to steel or stainless steel media for fine finishing and used with Raytech's Compound D. Please note that there is a break-in period of 4-6 hours required. Mixing in the 1mm and 2mm in with larger sized is recommended for good vibratory action. $95.37 |  The alternative to steel or stainless steel media for fine finishing and used with Raytech's Compound D. Please note that there is a break-in period of 4-6 hours required. Mixing in the 1mm and 2mm in with larger sized is recommended for good vibratory action. $95.37 |
 The alternative to steel or stainless steel media for fine finishing and used with Raytech's Compound D. Please note that there is a break-in period of 4-6 hours required. Mixing in the 1mm and 2mm in with larger sized is recommended for good vibratory action. $93.44 |  The alternative to steel or stainless steel media for fine finishing and used with Raytech's Compound D. Please note that there is a break-in period of 4-6 hours required. Mixing in the 1mm and 2mm in with larger sized is recommended for good vibratory action. $95.31 |
 The alternative to steel or stainless steel media for fine finishing and used with Raytech's Compound D. Please note that there is a break-in period of 4-6 hours required. Mixing in the 1mm and 2mm in with larger sized is recommended for good vibratory action. $97.31 |  Produces excellent final finish especially on stone and metal. $130.54 |
 The clean-running light media that is between ceramic and plastic bonds. Metal removal is not quite as fast on bulk or dense materials as ceramic, but measurably faster than plastic. Finishability is finer than ceramic and brighter than the standard opaque finish produced by plastic. Density - 65 lb./Cu. Ft. 5/8". $129.60 |  A corn-cob based media treated with Raytech's proprietary polishing compound, performs equal to, or better than Dri Shine I. Clean to use; rouge stain is eliminated. Density - 30 lb./Cu. Ft. $138.70 |
 Ceramic media is the heaviest media and is also the fastest finisher. Bonded of the highest quality materials available, selected aluminum oxide abrasives produce constant quality. This durable, long- lasting media is extremely versatile for deburring machined, cast or fabricated parts. Density - 90 lb./ Cu. Ft. $137.52 |  Formulated for very fine surface conditioning. Low R.M.S. finishes are commonly achieved. Plastic medias are widely used in the precision metal industries. Also due to fine surface finishes achieved, parts are prepared for preplate, pre-anodize, or decorative polishing. Brown, V-cut, Cone (medium cut, Green (light cut), and White (very fine cut). Density-55lb. per cu. ft. 1/2". $141.80 |
 Formulated for very fine surface conditioning. Low R.M.S. finishes are commonly achieved. Plastic medias are widely used in the precision metal industries. Also due to fine surface finishes achieved, parts are prepared for preplate, pre-anodize, or decorative polishing. Brown, V-cut, Cone (medium cut, Green (light cut), and White (very fine cut). Density-55lb. per cu. ft. 9/16". $152.15 |  A fast form of tumbling used to burnish metal to a mirror bright finish. Uniform in size and shape, non-abrasive and carefully tempered to ensure long life. Sold in 10 lb. packages.Similar to balls, but works into crevices better. $157.74 |
 Ceramic media is the heaviest media and is also the fastest finisher. Bonded of the highest quality materials available, selected aluminum oxide abrasives produce constant quality. This durable, long-lasting media is extremely versatile for deburring machined, cast or fabricated parts. Density - 90 lb./ Cu. Ft. 3/8". $171.89 |  A fast form of tumbling used to burnish metal to a mirror bright finish. Uniform in size and shape, non-abrasive and carefully tempered to ensure long life. Sold in 10 lb. packages. A combination of 3/16" balls, 3/16" ball cones, 1/8" x 3/8" pins and 1/8" diagonals for maximum coverage on a wide variety of pieces. $170.95 |
 A fast form of tumbling used to burnish metal to a mirror bright finish. Uniform in size and shape, non-abrasive and carefully tempered to ensure long life. Sold in 10 lb. packages. This is a general purpose media. $181.27 |  The alternative to steel or stainless steel media for fine finishing and used with Raytech's Compound D. Please note that there is a break-in period of 4-6 hours required. Mixing in the 1mm and 2mm in with larger sized is recommended for good vibratory action. $236.12 |
 The alternative to steel or stainless steel media for fine finishing and used with Raytech's Compound D. Please note that there is a break-in period of 4-6 hours required. Mixing in the 1mm and 2mm in with larger sized is recommended for good vibratory action. $237.92 |  The alternative to steel or stainless steel media for fine finishing and used with Raytech's Compound D. Please note that there is a break-in period of 4-6 hours required. Mixing in the 1mm and 2mm in with larger sized is recommended for good vibratory action. $237.92 |
 The alternative to steel or stainless steel media for fine finishing and used with Raytech's Compound D. Please note that there is a break-in period of 4-6 hours required. Mixing in the 1mm and 2mm in with larger sized is recommended for good vibratory action. $249.79 |  The alternative to steel or stainless steel media for fine finishing and used with Raytech's Compound D. Please note that there is a break-in period of 4-6 hours required. Mixing in the 1mm and 2mm in with larger sized is recommended for good vibratory action. $249.79 |
 The clean-running light media that is between ceramic and plastic bonds. Metal removal is not quite as fast on bulk or dense materials as ceramic, but measurably faster than plastic. Finishability is finer than ceramic and brighter than the standard opaque finish produced by plastic. Density - 65 lb./Cu. Ft. 5/8". $294.28 |  The clean-running light media that is between ceramic and plastic bonds. Metal removal is not quite as fast on bulk or dense materials as ceramic, but measurably faster than plastic. Finishability is finer than ceramic and brighter than the standard opaque finish produced by plastic. Density - 65 lb./Cu. Ft. $313.04 |
 Formulated for very fine surface conditioning. Low R.M.S. finishes are commonly achieved. Plastic medias are widely used in the precision metal industries. Also due to fine surface finishes achieved, parts are prepared for preplate, pre-anodize, or decorative polishing. Brown, V-cut, Cone (medium cut, Green (light cut), and White (very fine cut). Density-55lb. per cu. ft. 1/2". $320.90 |  Ceramic media is the heaviest media and is also the fastest finisher. Bonded of the highest quality materials available, selected aluminum oxide abrasives produce constant quality. This durable, long- lasting media is extremely versatile for deburring machined, cast or fabricated parts. Density - 90 lb./ Cu. Ft. $326.42 |
 Formulated for very fine surface conditioning. Low R.M.S. finishes are commonly achieved. Plastic medias are widely used in the precision metal industries. Also due to fine surface finishes achieved, parts are prepared for preplate, pre-anodize, or decorative polishing. Brown, V-cut, Cone (medium cut, Green (light cut), and White (very fine cut). Density-55lb. per cu. ft. 9/16". $346.99 |  A fast form of tumbling used to burnish metal to a mirror bright finish. Uniform in size and shape, non-abrasive and carefully tempered to ensure long life. Sold in 10 lb. packages. Tapered to a point, ideal for getting into deep recesses. $317.76 |
 A fast form of tumbling used to burnish metal to a mirror bright finish. Uniform in size and shape, non-abrasive and carefully tempered to ensure long life. Stainless steel is rust and corrosion-resistant, making it ideal for use in wet, flow-through systems. 10 lbs. (4.5 kg) boxes. Similar to balls, but works into crevices better. $348.67 |  Ceramic media is the heaviest media and is also the fastest finisher. Bonded of the highest quality materials available, selected aluminum oxide abrasives produce constant quality. This durable, long- lasting media is extremely versatile for deburring machined, cast or fabricated parts. Density - 90 lb./ Cu. Ft. 3/8". $399.29 |
 A fast form of tumbling used to burnish metal to a mirror bright finish. Uniform in size and shape, non-abrasive and carefully tempered to ensure long life. Stainless steel is rust and corrosion-resistant, making it ideal for use in wet, flow-through systems. 10 lbs. (4.5 kg) boxes. $383.06 |  A fast form of tumbling used to burnish metal to a mirror bright finish. Uniform in size and shape, non-abrasive and carefully tempered to ensure long life. Stainless steel is rust and corrosion-resistant, making it ideal for use in wet, flow-through systems. 10 lbs. (4.5 kg) boxes. A combination of 3/16" balls, 3/16" ball cones, 1/8" x 3/8" pins and 1/8" diagonals for maximum coverage on a wide variety of pieces. $334.80 |
 Formulated for very fine surface conditioning. Low R.M.S. finishes are commonly achieved. Plastic medias are widely used in the precision metal industries. Also due to fine surface finishes achieved, parts are prepared for preplate, pre-anodize, or decorative polishing. Brown, V-cut, Cone (medium cut, Green (light cut), and White (very fine cut). Density-55lb. per cu. ft. 1/4". $440.14 |  A fast form of tumbling used to burnish metal to a mirror bright finish. Uniform in size and shape, non-abrasive and carefully tempered to ensure long life. Stainless steel is rust and corrosion-resistant, making it ideal for use in wet, flow-through systems. 10 lbs. (4.5 kg) boxes. Large surface areas with beveled edges, ideal for corner work. $429.95 |
 A fast form of tumbling used to burnish metal to a mirror bright finish. Uniform in size and shape, non-abrasive and carefully tempered to ensure long life. Stainless steel is rust and corrosion-resistant, making it ideal for use in wet, flow-through systems. 10 lbs. (4.5 kg) boxes. Similar to balls, but works into crevices better. $438.65 |  Recommended for fine finishing and burnishing precious metals, brass, bronze and similar materials with plastic, ceramic or metal media. Supplied with Raytech MFA metal finishing kits. Use approximately 1 tsp. per pint. $425.00 |
 Formulated for very fine surface conditioning. Low R.M.S. finishes are commonly achieved. Plastic medias are widely used in the precision metal industries. Also due to fine surface finishes achieved, parts are prepared for preplate, pre-anodize, or decorative polishing. Brown, V-cut, Cone (medium cut, Green (light cut), and White (very fine cut). Density-55lb. per cu. ft. 1/4" $450.00 |  Formulated for very fine surface conditioning. Low R.M.S. finishes are commonly achieved. Plastic medias are widely used in the precision metal industries. Also due to fine surface finishes achieved, parts are prepared for preplate, pre-anodize, or decorative polishing. Brown, V-cut, Cone (medium cut, Green (light cut), and White (very fine cut). Density-55lb. per cu. ft. 1/4". $450.00 |
 A fast form of tumbling used to burnish metal to a mirror bright finish. Uniform in size and shape, non-abrasive and carefully tempered to ensure long life. Stainless steel is rust and corrosion-resistant, making it ideal for use in wet, flow-through systems. 10 lbs. (4.5 kg) boxes. Tapered to a point, ideal for getting into deep recesses. $480.00 |  The alternative to steel or stainless steel media for fine finishing and used with Raytech's Compound D. Please note that there is a break-in period of 4-6 hours required. Mixing in the 1mm and 2mm in with larger sized is recommended for good vibratory action. $555.00 |
 Recommended for fine finishing and burnishing precious metals, brass, bronze and similar materials with plastic, ceramic or metal media. Supplied with Raytech MFA metal finishing kits. Use approximately 1 tsp. per pint. $33.50 |  Used dry, produces a brighter finish when tumbled for 12 to 24 hours. Absorbs moisture. $41.69 |
 A liquid flo-thru compound concentrate, uniquely formulated for all metals and plastics. As a non-foaming compound, soils that can load the media and darken parts are quickly flushed from the processing channel, resulting in faster cycle times and cleaner parts. Mix 2% dilution for flo-thru. $63.18 |  Uniquely formulated liquid compound for use with steel shot. Also can be used as storage compound due to rust inhibitors in the formulation.Dilute 2% to water. $69.24 |